Garage floor coating video
A real customer install in Dallas-Fort Worth, filmed from the moment the truck pulls up to the moment the floor is finished. Fifty nine seconds, no narration.
0:59 long Filmed on a real job Flake floor, polyaspartic
What you are watching
The video has no voiceover, so here is what each part of it is showing you.
The truck arrives at the house. Everything needed for the floor is already on it, including the grinder and the vacuums.
Meeting the homeowner in the empty garage. Clearing the floor is the main thing we ask of you, along with parking on the street for the day.
Confirming the flake color against a physical sample board, on site, before anything goes down.
The planetary grinder comes down the truck ramp.
Diamond grinding the slab. This is the step that opens the concrete up so the coating can key into it. The vacuum runs the whole time, so the garage does not fill with dust.
A hand grinder takes the edges, the corners and the apron, everywhere the big machine cannot reach.
Cracks get chased open with a blade. Filling a crack without opening it first is how you get a line that comes back through the finish.
Cracks and holes filled, then ground flat again so the repair sits level with the rest of the slab.
Material mixed at the truck. Polyaspartic has a short working window, so it is mixed in batches as the crew needs it.
The base coat is cut in by hand along the walls and around the door tracks.
Flake goes into that wet edge straight away, by hand, before it can start to set.
The base coat is squeegeed out across the open floor and back rolled to an even film.
Flake is broadcast over the wet coat until the floor stops taking any more. That is what full flake means.
Once it has cured, the loose flake gets scraped back. This is slow, unglamorous work, and it is what makes the floor smooth underfoot.
Scraped flake is vacuumed up and bagged at the truck.
Edges, corners and the garage door line detailed by hand.
The whole floor, flaked and swept, before the top coat.
The clear polyaspartic top coat goes down over the whole floor. This is the layer you actually walk and park on.
The finished surface, close up, with the flake locked under the clear coat.
The finished garage, wall to wall. The blue wall tape is still down, which is the last thing to come off.
Worth watching for
Most coating videos look alike until you know what to look at. These are the moments that decide whether a floor lasts.
At 0:07 that is a diamond grinder, not acid. Acid etching is faster and cheaper, and a coating laid over an etched slab has far less to hold on to.
At 0:14 the crack gets cut wider on purpose. Skipping that step is why cracks telegraph back through a new floor later on.
At 0:31 the floor disappears under flake. A light sprinkle covers less and shows every scuff. Full flake is more material and more scraping.
The people grinding at 0:07 are the people top coating at 0:48. Nothing on this job is handed to a subcontractor.
If you would rather read
A polyaspartic flake floor is four layers of work, not one. First the concrete is mechanically ground so the surface is open and clean. Then every crack, pit and control joint is repaired and ground back flat. Then a polyaspartic base coat goes down and decorative flake is broadcast into it while it is still wet. Finally, once the flake has cured and the loose material has been scraped and vacuumed off, a clear polyaspartic top coat seals the whole thing.
The grinding and the scraping are the two steps that take the longest and the two that get skipped most often. Everything you can see in the finished floor depends on them.
Cure time. The floor in the video is walkable the next morning and ready to park on after about 48 hours. It also does not show the color options, because this house chose one flake blend out of a much longer list.
Every interior floor we install carries a lifetime warranty for as long as you live in the home. If the coating ever peels or lifts, we come back and fix it. What the warranty covers.
The full written install process breaks the same job into nine steps with photographs. The floor colors page shows every flake blend we carry, and polyaspartic compared with polyurea and epoxy explains why the material in this video was chosen.
Answer a few questions about your garage and get your exact price in 60 seconds. No home visit. No salesman. The number you see is the number on the invoice.