Tyre loads and jack points
An aircraft puts its weight through a very small contact patch, and a jack puts it through a smaller one still. Where the aircraft actually sits, and where it gets lifted, changes the build specification across the bay.
Hangar floor coating
A hangar floor carries tyre loads and jack points, takes fuel and hydraulic fluid, and has to stay clean enough that nothing comes off it and goes into an engine. We diamond grind the slab, repair what is under it and lay the system the building calls for. Epoxy, polyaspartic, polished concrete and grind and seal are all commercial systems we install, and the site walk is what decides which one.
Site walk before we quote · Written scope, no surprise change orders · 5.0 from 1,200+ Google reviews
What a hangar floor takes
Specify the floor around these and it lasts. Specify it around how it looks on the day the door opens and you are grinding it off again in two years.
An aircraft puts its weight through a very small contact patch, and a jack puts it through a smaller one still. Where the aircraft actually sits, and where it gets lifted, changes the build specification across the bay.
On bare or sealed only concrete these soak in, stain the slab and keep coming back up. On a sealed surface they stay on top, which means they get wiped instead of absorbed.
Maintenance chemistry is harder on a floor than anything a car park sees, and it lands on the same spots repeatedly. Chemical resistance is a specification here rather than a bonus.
Hard small wheels under load, turning in the same places every day. That is what scrubs a floor open, and it is concentrated at the door line and around the stands.
A hangar door open all day puts direct sunlight on the apron and the first stretch of floor inside it. Ultraviolet stability is why that strip is specified differently from the back of the building.
An uncoated slab gives off fine dust continuously, and in a hangar that dust is foreign object debris waiting to happen. Sealing the slab stops it at the source rather than sweeping it toward the door.
Which system goes in a hangar
Most people call every commercial floor epoxy, and the word is doing a lot of work. These are the four systems we actually install. The choice comes down to what rolls across the floor, what spills on it, how many hours we have between shifts and how it needs to look.
The surface
On the left, the kind of span this page is written for. On the right, one of our finished surfaces photographed close enough to see the texture.
How a hangar job runs
You cannot empty a hangar for a week, so the schedule is built around your movements rather than ours.
We come out and look at the slab, the door line, the stands, the drains and the joints. Square footage off a drawing does not tell us what is already on the concrete, where the aircraft actually sits or how much moisture is coming up through the slab.
You get the areas, the preparation method, the system by zone, the door line detail and the warranty terms in writing. No surprise change orders halfway through, because the walk is where the surprises get found.
Nights, weekends and phased bays. One bay is down while the rest of the hangar keeps working, then we move. Tell us your quietest week and we will work to it.
The slab is ground open so the system bonds to concrete rather than to old sealer or a failing coating. Cracks, spalling and old anchor holes are repaired, and the joints at the door line are detailed rather than coated over.
The system specified at the walk goes down in order, with the door line and the apron strip specified for the sun that lands on them. Foot traffic the next morning on a polyaspartic build.
The commercial floor coating page covers how we work in a building that cannot close, and the installation process goes through every step in detail.
Who it is for
One or two aircraft, a clean floor that is part of how the hangar presents, and an owner who notices the door line. This is where the finish and the specification are doing equal work.
Fluids, tooling, stands and constant wheeled traffic in the same bay. The chemistry that lands on the floor usually drives the specification more than the aircraft weight does.
More movements, more people walking the floor and a building that customers see. Dust control and grip at the door line tend to come up before anything else.
Warranty
Service area
Our own crews, not subcontractors. Commercial work is quoted after a site walk.
Questions
Yes. Epoxy is one of four commercial systems we install, alongside polyaspartic, polished concrete and grind and seal. In a hangar the answer is often a build that uses more than one: an epoxy base for thickness where the loads are concentrated, an ultraviolet stable top coat at the door line where the sun lands. Which combination is right comes out of the site walk.
That is a build specification rather than a yes or no. An aircraft puts its weight through a small contact patch and a jack puts it through a smaller one, so what matters is where the load actually lands. We specify the build around that, which is why the walk matters more than the square footage.
On a sealed surface it stays on top where it can be wiped, instead of soaking into the slab and staining it permanently. Which system we specify depends on what is actually landing on the floor and how often, which is one of the questions we ask at the walk.
Polyaspartic is ultraviolet stable, which is why it is specified for the door line and the apron strip where direct sun reaches the floor. On a build that uses an epoxy base, the top coat is what takes the sun, and the door line is specified separately from the back of the hangar for exactly that reason.
Yes, and it is one of the main reasons hangars call. An uncoated slab gives off fine dust continuously, and sweeping moves it toward the door rather than removing it. Sealing the slab stops it at the source, whether that is a full coated build, polished concrete or a grind and seal.
Yes, on most jobs. Nights, weekends and phased bays, so one bay is down while the rest of the building keeps working, then we move across. Give us your quietest week and your movement schedule and we will build around them.
Often, yes. Polished concrete is the slab itself ground and densified, so there is no film on top to chip under a jack pad, and it reflects light across a wide span, which lifts the light level in a tall building. We sell polished concrete and grind and seal on commercial work, so both are genuinely on the table when we walk your hangar.
We quote after a site walk, because the price turns on the condition of the slab, the system the building calls for, the door line detail, the joint detail and how much of the work has to happen around your movements. You get a written scope rather than a number on a card. Request a quote or call (469) 990-9990.
One bay, the door line or the whole span. We will walk the building, write the scope and schedule it around your movements.
Site walk before we quote · Commercial floor coating · Warranty · hello@mygaragefloors.com