Hangar floor coating

Hangar floor coating for aircraft weight, fuel and hydraulic fluid.

A hangar floor carries tyre loads and jack points, takes fuel and hydraulic fluid, and has to stay clean enough that nothing comes off it and goes into an engine. We diamond grind the slab, repair what is under it and lay the system the building calls for. Epoxy, polyaspartic, polished concrete and grind and seal are all commercial systems we install, and the site walk is what decides which one.

Site walk before we quote · Written scope, no surprise change orders · 5.0 from 1,200+ Google reviews

An aircraft hangar with a seamless light reflecting floor running out to the door line
LoadsSpecified for tyre loads, jack points and tugs
FluidsFuel, oil and hydraulic fluid sit on top of a sealed floor
CleanA sealed slab stops giving off the dust that becomes FOD
OpenNights, weekends and phased bays keep the hangar working

What a hangar floor takes

Six things a hangar slab deals with that a garage floor never does.

Specify the floor around these and it lasts. Specify it around how it looks on the day the door opens and you are grinding it off again in two years.

Tyre loads and jack points

An aircraft puts its weight through a very small contact patch, and a jack puts it through a smaller one still. Where the aircraft actually sits, and where it gets lifted, changes the build specification across the bay.

Fuel and oil drips

On bare or sealed only concrete these soak in, stain the slab and keep coming back up. On a sealed surface they stay on top, which means they get wiped instead of absorbed.

Hydraulic fluid and solvent

Maintenance chemistry is harder on a floor than anything a car park sees, and it lands on the same spots repeatedly. Chemical resistance is a specification here rather than a bonus.

Tugs, dollies and toolboxes

Hard small wheels under load, turning in the same places every day. That is what scrubs a floor open, and it is concentrated at the door line and around the stands.

Sun through an open door

A hangar door open all day puts direct sunlight on the apron and the first stretch of floor inside it. Ultraviolet stability is why that strip is specified differently from the back of the building.

Dust and FOD

An uncoated slab gives off fine dust continuously, and in a hangar that dust is foreign object debris waiting to happen. Sealing the slab stops it at the source rather than sweeping it toward the door.

Which system goes in a hangar

Four commercial systems, and the building decides.

Most people call every commercial floor epoxy, and the word is doing a lot of work. These are the four systems we actually install. The choice comes down to what rolls across the floor, what spills on it, how many hours we have between shifts and how it needs to look.

Epoxy

  • Builds thick, which is what carries concentrated tyre and jack loads.
  • Fills and levels a slab that has been patched, cored or repaired over the years.
  • Takes a longer cure, which suits a bay that can stay empty for a stretch.
  • Often the base of a build with a faster, ultraviolet stable top coat over it.

Polyaspartic

  • Cures fast, so a bay goes down overnight and takes the aircraft back the next day.
  • Chemically resistant to fuel, oil, hydraulic fluid and maintenance solvents.
  • Ultraviolet stable, which is why it is specified at the door line where the sun lands.
  • Stays slightly flexible, so slab movement does not crack the finish open.
  • Low odour and low VOC, so the building is usable again quickly.

Polished concrete

  • The slab itself, ground and densified, so there is no film on top to chip under a jack pad.
  • Reflects light across a wide span, which lifts the light level in a tall building.
  • Holds up to constant wheeled traffic from tugs, stands and dollies.
  • Wants a sound slab underneath, which is one of the things the walk establishes.

Grind and seal

  • The slab ground flat and sealed, so a dusty floor becomes a cleanable one.
  • Stops concrete dust at the source, which in a hangar is a safety answer as much as a tidiness one.
  • The quickest route to a sealed surface across a large span.
  • Can be built on later, so a hangar can be sealed now and specified further when it suits.

The surface

What a finished commercial floor looks like up close.

On the left, the kind of span this page is written for. On the right, one of our finished surfaces photographed close enough to see the texture.

A wide commercial span with a seamless light reflecting coated floor
A wide span. The light has to carry from the door to the back wall, and the floor is most of what carries it.
Close up of a finished blue gray flake floor meeting bare concrete at the door line
One of our finished surfaces up close. The texture you can see is the flake, and it is what gives a wet floor its grip.

How a hangar job runs

Five steps, and the hangar keeps working through all of them.

You cannot empty a hangar for a week, so the schedule is built around your movements rather than ours.

  1. Site walk before we quote

    We come out and look at the slab, the door line, the stands, the drains and the joints. Square footage off a drawing does not tell us what is already on the concrete, where the aircraft actually sits or how much moisture is coming up through the slab.

  2. A written scope, not a number on a card

    You get the areas, the preparation method, the system by zone, the door line detail and the warranty terms in writing. No surprise change orders halfway through, because the walk is where the surprises get found.

  3. We schedule around your movements

    Nights, weekends and phased bays. One bay is down while the rest of the hangar keeps working, then we move. Tell us your quietest week and we will work to it.

  4. Diamond grinding and repair

    The slab is ground open so the system bonds to concrete rather than to old sealer or a failing coating. Cracks, spalling and old anchor holes are repaired, and the joints at the door line are detailed rather than coated over.

  5. Build, then an ultraviolet stable top coat

    The system specified at the walk goes down in order, with the door line and the apron strip specified for the sun that lands on them. Foot traffic the next morning on a polyaspartic build.

The commercial floor coating page covers how we work in a building that cannot close, and the installation process goes through every step in detail.

Who it is for

Private hangars, maintenance shops and flight schools.

Private and corporate hangars

One or two aircraft, a clean floor that is part of how the hangar presents, and an owner who notices the door line. This is where the finish and the specification are doing equal work.

Maintenance and MRO shops

Fluids, tooling, stands and constant wheeled traffic in the same bay. The chemistry that lands on the floor usually drives the specification more than the aircraft weight does.

Flight schools and FBO facilities

More movements, more people walking the floor and a building that customers see. Dust control and grip at the door line tend to come up before anything else.

Warranty

What is covered, in writing, before you sign.

Written into your proposal on a hangar floor
Own crews in all six metros, not subcontractors
On a hangar floor
The warranty terms are written into your proposal, because the right cover depends on what the floor is going to take. A maintenance bay is a different floor from a storage bay, and quoting one number for both would mean one of you was being sold the wrong promise.
Why we walk the building first
Square footage off a drawing does not tell us whether there is a sealer on the slab, how much moisture is coming up through it, where the water goes or which areas need extra grip. The walk is where the surprises get found, which is why there are no surprise change orders afterwards.
What no coating covers
New movement in the slab underneath. Concrete cracks because the ground moves, and no coating stops that, ours or anybody else’s. If we can see a slab that is likely to move, or moisture pushing up through it, we tell you at the site walk rather than after you have paid. The warranty page lists every term and every exclusion.

Service area

Six metros across Texas and Oklahoma.

Our own crews, not subcontractors. Commercial work is quoted after a site walk.

Questions

Hangar floor coating questions

Do you do commercial epoxy flooring in hangars?

Yes. Epoxy is one of four commercial systems we install, alongside polyaspartic, polished concrete and grind and seal. In a hangar the answer is often a build that uses more than one: an epoxy base for thickness where the loads are concentrated, an ultraviolet stable top coat at the door line where the sun lands. Which combination is right comes out of the site walk.

Will it take the weight of an aircraft?

That is a build specification rather than a yes or no. An aircraft puts its weight through a small contact patch and a jack puts it through a smaller one, so what matters is where the load actually lands. We specify the build around that, which is why the walk matters more than the square footage.

What happens when fuel or hydraulic fluid gets on it?

On a sealed surface it stays on top where it can be wiped, instead of soaking into the slab and staining it permanently. Which system we specify depends on what is actually landing on the floor and how often, which is one of the questions we ask at the walk.

Does the floor yellow where the door is open?

Polyaspartic is ultraviolet stable, which is why it is specified for the door line and the apron strip where direct sun reaches the floor. On a build that uses an epoxy base, the top coat is what takes the sun, and the door line is specified separately from the back of the hangar for exactly that reason.

Will it help with dust and FOD?

Yes, and it is one of the main reasons hangars call. An uncoated slab gives off fine dust continuously, and sweeping moves it toward the door rather than removing it. Sealing the slab stops it at the source, whether that is a full coated build, polished concrete or a grind and seal.

Can we keep using the hangar while you install?

Yes, on most jobs. Nights, weekends and phased bays, so one bay is down while the rest of the building keeps working, then we move across. Give us your quietest week and your movement schedule and we will build around them.

Is polished concrete an option for a hangar?

Often, yes. Polished concrete is the slab itself ground and densified, so there is no film on top to chip under a jack pad, and it reflects light across a wide span, which lifts the light level in a tall building. We sell polished concrete and grind and seal on commercial work, so both are genuinely on the table when we walk your hangar.

What does hangar floor coating cost?

We quote after a site walk, because the price turns on the condition of the slab, the system the building calls for, the door line detail, the joint detail and how much of the work has to happen around your movements. You get a written scope rather than a number on a card. Request a quote or call (469) 990-9990.

Tell us what your hangar floor takes all day.

One bay, the door line or the whole span. We will walk the building, write the scope and schedule it around your movements.

Site walk before we quote · Commercial floor coating · Warranty · hello@mygaragefloors.com